Environmental simulation in climatic chambers and wind tunnels
Dehumidifiers: It's all a question of adjustability
Best suited for the simulation of environmental conditions for tests in the automotive industry are Trotec dehumidifiers of the TTR series marked with "D", because they are so easily regulated. You would like to test the behaviour of rubber seals in dry heat? And damp cold? No problem with the Duoventic regulation.
In climatic chambers and wind tunnels three factors need to be simulated at the best possible rate: air temperature, wind strength and humidity. For the latter, the automotive industry needs dehumidifiers, which also perform well at dew points below 0°C, as well as high-performance desiccant dehumidifiers.
Desiccant dehumidifiers of the TTR series – the most economical of their kind
With our robust dehumidifiers of the TTR series climatic chambers and wind tunnels in the automotive industry are also ideally equipped: The TTR adsorption devices ensure an efficient high-capacity dehumidification. And with their internal heat recovery as well as the high level of resilience and performance of the special rotors the adsorption dryers of the TTR series are among the most economical dehumidifiers of their kind.
Models marked with "D" as in the Duoventic air volume regulation
The TTR series comprises stationary and mobile desiccant dehumidifiers. In climatic chambers and wind tunnels mostly compact mobile devices are being used. For this type of application we recommend i.a. TTR 400 D and TTR 500 D. All TTR models of type "D" as standard come not only equipped with two separate air flow ducts according to the TTR Trisorp Dual principle of operation but also with the innovative Duoventic air volume regulation. Therefore, both fans of the separate air circuits can be controlled independently via an infinitely variable electronic regulation. Thanks to Duoventic, you can always use the full potential in the climatic chamber fast and in line with demand without any conversions while at the same time configuring every climate scenario with only one device.
Drafting and test run: make use of our industrial services
For industrial customers the Trotec Group not only offers devices, but solutions. We draft the dehumidification concept for your climatic chamber or wind tunnel and test it beforehand in trial operation using mobile devices. Only after measurements have proved that the humidity level can be controlled as desired will your final solution be launched.
Make use of our best practice industrial services
You can count on our experts
In order to precisely calculate the demand in the industry and to develop tailor-made concepts for climate conditioning experienced climate specialists are needed. Rely on our team of experts as well as the industrial services: We analyse the individual requirement situation with you present on site, determine the specific demand for devices and develop a tailor-made project solution right up to the exact positioning of the devices.
Before the planned stationary units are installed, our service team first works with mobile versions of the drying units as part of a trial run. These can be put up without any difficulty or the need for structural changes.
During this validation phase we document all relevant climate parameters such as air temperature, relative humidity, dew point or flow rate for a final optimization of the requirement calculation.
Trotec is the only provider of this advantage:
Thanks to the unique option of non-binding trial operation you will invest solely in solutions which have verifiably proven their worth in everyday operation meeting your individual on-site requirements. The stationary units will not be ordered until you are fully satisfied with our concept. The only costs incurred consist of an inexpensive hiring flat rate for the time of test operation.
Just give us a call at +49 2452 962-777 – our industry consultants will be pleased to help you personally and provide information regarding our best practice industrial services. Or send a request indicating your personal requirements directly to our industry experts. We will answer promptly!
Since every industrial undertaking has characteristic process flows, installations and facilities, every air treatment solution demands case-specific device configurations. All in all, the combined effects of air currents, humidity conditions and temperature fluctuations are often hard to calculate on a purely theoretical basis, e.g. in airlock areas or on conveying paths. The consequence: Unnecessary additional costs due to an overestimated demand or – even worse – solutions not working sufficiently in real life.
Upon request, we will readily produce tailor-made desiccant dehumidifiers as special models “made in Germany” perfectly geared to your needs, e.g.:
- TTR industrial desiccant dehumidifiers with hygienic design
- TTR industrial desiccant dehumidifiers for PWIS-free dry air
- TTR industrial desiccant dehumidifiers with extremely low dew point
Makes use of the possibility of having special models with tailored components for your individual needs planned, designed and manufactured in close consultation with our specialists.
Click here to find out more ...
Environmental simulation climate chamber